Search
Browsing 2014 by Title
Now showing items 10-20 of 20
-
Нанокристаллические покрытия элементов штамповой оснастки
(БрГТУ, 2014)В работе приводятся результаты исследований нового материала для штамповой оснастки, основу которого составляют карбонитрид циркония и алмазоподобный углерод, анализируются результаты производственных испытаний пуансонов с упрочняющими покрытия.2019-08-23
-
Напряженно-деформированное состояние пробивного пуансона при поверхностной плазменной закалке рабочей зоны и интенсивном теплоотводе
(БрГТУ, 2014)В данной статье рассматривается моделирование процесса поверхностной плазменной закалки рабочей зоны пробивного пуансона с определением оптимальных режимов этого процесса, обеспечивающих высокую поверхностную прочность с сохранением структуры его внутренней области.2019-08-23
-
Неразрушающий метод и устройство контроля однородности физико-механических свойств TiNi изделий
(БрГТУ, 2014)Установлено, что в проволочных образцах никелида титана находящихся изначально в аустенитном состоянии при перемещении вдоль образца охлаждаемого (до температуры ниже Mк) участка возникает термокинетическая ЭДС обусловленная прямым фазовым превращением. В процессе перемещения зоны охлаждения через ...2019-08-26
-
Разработка технологии изготовления рубильных ножей с учетом результатов экспериментальных исследований модельных образцов, и проведение производственных испытаний ножей
(БрГТУ, 2014)В результате проведенных экспериментальных исследований модельных образцов установлено, что образцы рубильных ножей с небольшими размерами и относительно большой толщиной после ТО не имеют остаточных деформаций. Более тонкие образцы прямоугольной формы (длиной более 300 мм), после ТО имеют остаточную ...2019-08-26
-
Разрушение поверхности раздела двух несмешивающихся жидкостей при эмульгировании
(БрГТУ, 2014)Представлен анализ решения вопроса охраны труда работников от вредного воздействия на здоровье человека отработавших нефтепродуктов и растворов технических моющих средств путем приготовления мелкодисперсной эмульсии с последующем ее использовании в качестве смазки форм при производстве железобетонных ...2019-08-23
-
Расчет распределения легирующих компонентов Мп и Ga в мартенситной фазе монокристаллического ферромагнитного сплава гейслера Ni2MnGa у линзовидного остаточного некогерентного механического двойника
(БрГТУ, 2014)На основе четырехфункциональной модели линзовидного двойника выполнен расчет распределения Мп и Ga в ферромагнитном сплаве Гейслера Ni2MnGa. Определены области локализации легирующего компонента и характер его распределения у двойника.2019-08-23
-
Расчет эвольвентных зубчатых передач при курсовом проектировании деталей машин
(БрГТУ, 2014)Предлагаются расчетные зависимости для расчета на прочность цилиндрических, конических и планетарных эвольвентных зубчатых передач при курсовом проектировании деталей машин. Формулы удобны для применения в учебном процессе, так как в них, в отличие от существующих в технической литературе, соблюдаются ...2019-08-23
-
Совершенствование системы диагностирования бензиновых автомобильных двигателей
(БрГТУ, 2014)В статье предложено автоматизировать анализ данных, получаемых инструментальным виброакустическим методом совместно с данными других методов, при этом, для преодоления комбинаторной сложности предложено использовать математический аппарат нечеткой кластеризации.2019-08-26
-
Способы представления виброакустического сигнала для повышения эффективности диагностики зубчатых приводов
(БрГТУ, 2014)Рассмотрены основные способы представления виброакустического сигнала при диагностике многовальных зубчатых приводов. Достоинства и недостатки этих способов обоснованы результатами экспериментов. Вейвлетный анализ выделен как наиболее перспективный в виду существенных преимуществ. Однако исключать ...2019-08-23
-
Теоретический анализ возможности настройки по крайним (концевым) точкам механизма для заточки лезвия геликоидальных рубильных ножей
(БрГТУ, 2014)Приведена схема устройства и метод его настройки для затачивания режущей кромки геликоидального рубильного ножа длиной 300 мм, применяемого на деревообрабатывающих предприятиях республики Беларусь для производства технологической щепы. Теоретический анализ возможности настройки устройства по крайним ...2019-08-26
-
Фрактографические исследования изломов образцов с наплавленными покрытиями, полученных в условиях циклического нагружения
(БрГТУ, 2014)В работе приведены фрактографические исследования изломов образцов, полученных наплавкой проволокой с различным содержанием легирующих элементов и углерода. Разрушение образцов происходило в условиях циклического нагружения. Установлено, что при разрушении основы образца преобладает ямочный рельеф. ...2019-08-26